Residential pool engineering
We prepare structural designs for in-ground concrete pools and spas for pool builders and homeowners. The drawings set the shell, reinforcement and founding requirements to suit the soil test, and deal with nearby houses, retaining walls, slopes and sewers.
Aquatic engineering
Typical projects
- Concrete pools and spas for new and existing homes
- Pools on sloping blocks with retaining
- Pools near house footings or boundary walls
- Pools near sewers or in easements
- Plunge pools and pools on reactive clay
Problems this work solves
- Excavation next to the house
- A pool dug close to a house can undermine its footings. The design checks the load influence line from each nearby footing, commonly taken at about 30 degrees in sand, 45 in clay and 60 in rock, and calls for underpinning where the excavation crosses it.
- Groundwater and an empty pool
- An empty pool in wet ground can lift out of the ground. A hydrostatic valve and drainage below the floor relieve the pressure.
- Reactive clay
- Clay that swells and shrinks pushes on the shell. The design assumes a site classification and bearing capacity, and the builder confirms them against the soil test.
- Sewers and easements
- Pools near sewers, water mains and stormwater drains fall under QDC MP 1.4, and some service providers do not allow pools in easements at all.
What our engineering covers
Coreline's role is design, documentation, assessment and inspection. Construction, supply and installation sit with the builder and trades.
- Review of the site plan, soil test and survey
- Shell thickness and reinforcement design
- Founding design, including bored piers or screw piles where the ground needs them
- Details next to existing footings, retaining walls and boundaries
- Hydrostatic relief, drainage and edge details
- Notes for barrier, fencing and site drainage coordination
- Design certification for building approval
Design considerations
- Shotcrete shell thickness
- Shell thickness and a single layer of reinforcement with adequate cover to the water face are set by depth, soil and retained height. Thicker is not automatically better if the bar placement suffers.
- Retaining fill around the pool
- Where the pool wall retains fill or a neighbouring level, extra reinforcement and drainage are needed and the limits are stated on the drawings.
- Who confirms soil conditions
- Drawings rely on the soil test. If excavation reveals worse ground, the builder needs to stop and call the engineer before pouring.
What you typically receive
The exact deliverables are set in the fee proposal for each project.
- Pool structural drawings: site plan, pool plan, sections and details
- General notes on concrete, reinforcement, curing and filling
- Design certificate for building approval
- Reinforcement inspection where engaged
What to send us
- Site plan with pool position, house and boundaries
- Pool shape, size, depths and any spa, bench or steps
- Soil test or site classification
- Location of sewer and stormwater lines
- Photos or details of nearby retaining walls and structures
- Builder's preferred construction method
Standards and regulations that usually apply
Which documents govern a design depends on the project. These are the ones most often relevant here; we confirm the applicable editions for each job.
- AS 3600
- Design and construction of reinforced and prestressed concrete structures and members.
- AS 2870
- Site classification and the design of slabs and footings for houses, townhouses and similar buildings.
- QDC MP 1.4
- Building work over or near sewers, water mains and stormwater drains, including clearances and service provider approval.
- QDC MP 3.4
- Queensland's single pool safety standard for barriers. It does not cover the structural design of the pool shell.
Questions we are asked
How close can a pool be to my house?
There is no single distance; it depends on the depth of the pool, the depth of the house footings and the soil. If the pool excavation would cut below the load influence line from the house footing, the footing must be underpinned or the pool moved.
Do I need a soil test for a pool?
Yes, in almost all cases. The structural design assumes a site classification and bearing capacity, and the soil test confirms them. On sites with fill, rock or high reactivity, the soil test can change the design.
Why does a pool need a hydrostatic valve?
If groundwater builds up under an empty pool, it can lift the shell. A hydrostatic valve lets that water into the pool instead, relieving the pressure.
Do you work directly with pool builders?
Yes. Most residential pool designs are requested by the pool builder, who supplies the layout and soil test and receives the drawings and certification for approval.
Sources
Need residential pool engineering?
Tell us what you are building or assessing, where it is and what drawings or reports you already have. We will come back with questions, a scope and a fee.
- Phone
- 1300 924 666
- Registered engineer
- Mustafa Koc, RPEQ 35981 (Civil)
