Skip to content
Coreline Engineering

Timber and CLT design

We design timber structures in sawn timber, glulam, LVL and cross-laminated timber (CLT), from feature roof framing to timber floors and walls in low-rise buildings. Design is to AS 1720.1, with connections, moisture and fire treated as part of the structure.

Structural engineering

Typical projects

  • Architect-designed houses with exposed timber framing
  • Community halls, schools and pavilions with timber roofs
  • CLT floors and walls in low-rise commercial or residential buildings
  • Decks, pergolas and elevated walkways
  • Additions to existing timber-framed Queenslanders

Problems this work solves

Connections decide the design
Timber members are rarely the weak point. The bolts, screws and plates joining them usually govern, and they also govern how the structure looks.
Moisture and movement
Timber shrinks and swells across the grain. Details that trap water or restrain movement lead to splitting, decay and loosened fixings.
Vibration in timber floors
Light timber and CLT floors can meet strength limits and still feel bouncy. Floor vibration often sets the depth.

What our engineering covers

Coreline's role is design, documentation, assessment and inspection. Construction, supply and installation sit with the builder and trades.

  • Selection of timber products and grades for the application
  • Member and connection design to AS 1720.1
  • Floor vibration and deflection checks
  • Durability, moisture and exposure detailing
  • Coordination with the architect on exposed connections
  • Assessment of existing timber structures for alterations

Design considerations

Engineered timber supply
Glulam, LVL and CLT sizes and lead times vary by supplier. Confirming supply early avoids redesign when a section is unavailable.
Fire
Exposed mass timber chars at a predictable rate, which can be designed for, but the building class and certifier's approach determine whether encapsulation is needed.
Hybrid structures
Timber often works best combined with a concrete ground floor or steel transfer members. The interface between materials needs particular attention for movement and moisture.

What you typically receive

The exact deliverables are set in the fee proposal for each project.

  • Structural drawings with member sizes, grades and connection details
  • Bracing and tie-down design where outside the framing code
  • Design certification for building approval where required
  • Inspection certificates for frame inspections we carry out

What to send us

  • Architectural drawings, including any exposed-structure intent
  • Site address for wind classification
  • Preferred timber products or suppliers, if known
  • For existing buildings: photos and any original drawings
  • Building class and fire requirements, if already advised by the certifier

Standards and regulations that usually apply

Which documents govern a design depends on the project. These are the ones most often relevant here; we confirm the applicable editions for each job.

AS 1720.1
Design of timber structures, including engineered and mass timber products.
AS/NZS 1170 series
Structural design actions: permanent, imposed, wind, earthquake and other loads used in every structural design.
NCC (Building Code of Australia)
Performance requirements for buildings. In Queensland NCC 2022 applies until 30 April 2027 and NCC 2025 from 1 May 2027.

Questions we are asked

Is CLT practical for a low-rise building in Queensland?

It can be, particularly where a fast, light, dry build matters, such as building over existing structures or on soft ground. Supply, fire approach and termite and moisture protection need to be settled early, and cost should be compared with concrete on the same layout.

Why are timber floors sometimes bouncy even when they pass strength checks?

Timber floors are light, so footfall makes them vibrate more than concrete floors of similar span. Vibration criteria often require a deeper or stiffer floor than strength alone would need.

Can you design a raised addition to an old Queenslander?

Yes. We check the existing stumps, bearers and framing, design the new structure, and detail how the two are tied together so the old house carries only what it can.

Sources

Need timber and clt design?

Tell us what you are building or assessing, where it is and what drawings or reports you already have. We will come back with questions, a scope and a fee.

Registered engineer
Mustafa Koc, RPEQ 35981 (Civil)
Add company, role and timing (optional)

We use these details only to respond to your enquiry. See our privacy policy. Please do not attach or paste plans here; we will ask for them by email once we have spoken.

Call 1300 924 666Discuss your project