Structural engineering
Coreline designs and documents building structures in concrete, steel, timber and masonry, and assesses existing ones. Design and certification are carried out under a practising RPEQ, which Queensland law requires for professional engineering services in or for the state.
9 services
Most of the cost in a structure is set early. Grid spacing, slab type, transfer levels and the founding strategy are usually fixed before the architect's design development set is complete, and each of those decisions changes the quantity of concrete and steel on site and the number of trades needed to put it there. We prefer to be involved while those choices are still open, so the structural system is chosen on cost and buildability as well as on spans.
Our design work runs from concept options through to documentation for building approval and construction. Where an existing building is being altered, extended or bought, we inspect it, work out how load reaches the ground today, and report on what the proposed change does to that load path. Findings are written so that a builder, owner or certifier can act on them without a second meeting to explain the report.
We are based in Rochedale and work across Greater Brisbane and Queensland locations within about 500 km of the CBD. Site visits further out are planned around the project programme, and much of the design and coordination can be done from drawings, survey and a geotechnical report.
Structural engineering services
- Reinforced concrete designReinforced concrete design for slabs, beams, columns, walls and basements, documented for building approval and construction in south-east Queensland.
- Structural steel designSteel frame, portal frame, mezzanine, canopy and connection design for commercial and industrial buildings, documented for fabrication in Queensland.
- Precast and tilt-up concreteDesign of precast and tilt-up concrete panels, connections and temporary bracing for warehouses, commercial buildings and apartments in Queensland.
- Timber and CLT designStructural design of timber, glulam, LVL and cross-laminated timber (CLT) for houses, community buildings and low-rise commercial projects in Queensland.
- Steel fibre reinforced concrete slabsSteel fibre reinforced concrete (SFRC) ground slab design for warehouses and factories, covering racking loads, forklift traffic and joint layout.
- Masonry designStructural design of reinforced blockwork, loadbearing masonry and masonry retaining walls, plus new openings in existing walls, in south-east Queensland.
- Foundation designFoundation design for difficult ground: footings, rafts, bored piers and screw piles near existing buildings, sewers and slopes across Queensland.
- Structural assessments and auditsStructural audits, asset inspections and materials compliance checks for existing commercial, industrial and residential buildings in Queensland.
- Heritage structuresStructural assessment, repair and alteration design for heritage-listed and older buildings, keeping original fabric while meeting safety needs.
Also within this discipline
Work we take on as part of a wider engagement. Ask us if your project needs it.
- Revit-based structural documentation for projects coordinated through a shared BIM model
- Assessment of new building products and construction methods against the loads and exposure of a specific project
Questions we are asked
When do I need a structural engineer for a building project?
You need one whenever a building element carries load beyond what a deemed-to-satisfy or prescriptive solution covers, and in practice that is almost every commercial, industrial and multi-residential project. Footings, slabs, suspended floors, steel frames, retaining walls and alterations that remove or add load all need a design that a certifier can rely on.
Do structural engineers in Queensland have to be registered?
Yes, unless they work under the direct supervision of a registered engineer or to a prescriptive standard. The Professional Engineers Act 2002 requires a Registered Professional Engineer of Queensland (RPEQ) for professional engineering services in or for Queensland, and you can check any engineer's status on the BPEQ public register.
What should I send with a request for a structural proposal?
Send the current architectural drawings, the site address, any geotechnical report or soil test, survey if available, and the stage you are at (feasibility, development approval, building approval or construction). Tell us the programme and who else is on the design team, because coordination effort is a large part of the fee.
Which edition of the National Construction Code applies in Queensland?
In Queensland, NCC 2022 applies until 30 April 2027 and NCC 2025 applies from 1 May 2027. The edition that governs your project depends on when the building approval application is lodged, so confirm it with your building certifier early in design.
Have a project that needs engineering input?
Tell us what you are building or assessing, where it is and what drawings or reports you already have. We will come back with questions, a scope and a fee.
- Phone
- 1300 924 666
- Registered engineer
- Mustafa Koc, RPEQ 35981 (Civil)
